Thermostat Clicks But Heater Not Turning On Fan Works AC Runs But Heat No Start Repair Video

Thermostat Clicks But Heater Not Turning On Fan Works AC Runs But Heat No Start Repair Video

Welcome back to Kung Fu Maintenance! Wanted to tell you, show you, about one I had the other day. What happened was right at the end of the day I saw that there was a work order for a no heat call. Went and checked it out. The hydronic valves were turned off and turned those on. Came over to the thermostat and turned it on but nothing turned on. I could see. the flame signal here. Much like this one. Now usually when you do it you will hear the little click when it turns on. On that particular one I did hear the click and that kind of signified to me that the thermostat was working. I turned the fan to on. The fan kicked on. I turned the A/C on and the AC kicked on. Turned it to cool and auto. Lowered the temperature down and everything kicked on there right away. So I knew at that point that it wasn’t the service door switch. Didn’t know what it was but what I did was pullk the cover off.

Now before I do that I want to show you the little click. I will raise my temperature up so the heater will turn on a little bit. You hear that click? That’s signifying that my unit is getting ready to fire up as the heater has now been signaled to turn on. But underneath. I will show you here. What you have got is your red cold jumper and the red hot jumper wire. That fatter red wire that is back there. I got kind of lucky and noticed right away that the insulation part, even much like it is here, the insulation portion was up inside the screw port. So All I had to do was loosen the screw a little bit. Move the wire down a tiny bit so that the wire was actually making contact with the screw port so we would have continuity.

And that’s all it was. The screw instead of clamping the wire down was clamping the insulation down. Insulation was making contact so that the heater wasn’t turning on even though it was sending the call for heat from the thermostat. It wasn’t being transmitted through the hot wire so. Nice easy fix. Thought I would show it to you guys. Hope it saves you some trouble.You know.

It’s rare but these are the things that happen and a little bit on the troubleshooting that happens. Obviously if a wire is not making contact there things are not going to turn on. And one other thing I had checked on this which should be checked when a thermostat is not working. One thing to check on theses is the jumper pin or the switch setting. This one has a little switch down here where right is for gas heating and left is for electric heating. That particular one was set for electric heating which is common to all of my other units for hydronic heating. So it wasn’t that. So again it was that insulation that was blocking. So that the wire wasn’t making contact on the RH wire. Anyway. Thanks for watching! .

Dryer Not Drying? Cycling Thermostat Testing, Troubleshooting

Dryer Not Drying? Cycling Thermostat Testing, Troubleshooting

A cycling thermostat is a switch that is actuated by temperature change if your dryer does not heat at all you should test the thermostat for continuity at room temperature a continuity tests will determine if a continuous electrical path is present in the thermostat at room temperature the thermostat should have continuity no continuity means the electrical path is broken and the thermostat has failed you can choose from a variety of multimeters to perform the test for this demonstration we will use both analog and digital models when using an analog model first rotate the range selection dial to the lowest setting for ohms of resistance then calibrate the meter by pinching the probes together while adjusting the needle to read zero when using a digital model again rotate the dial to the lowest setting for ohms of resistance or resistance with tone if your meter has this option before you begin make sure the thermostat has been removed or isolated from the appliance some cycling thermostats have more than two terminals since the inner terminals are for a small heater only used to control the low heat setting test the park by touching the probes to the outer terminals only if the meter reading shows zero ohms of resistance the thermostat has continuity if the meters needle does not move or the digital display does not change significantly there is no continuity which means the thermostat has failed and will need to be replaced while the thermostat should display continuity at room temperature it should switch off or display no continuity when heated if the thermostat does not switch off when heated or switches off prematurely your dryer will be there overheat or heat improperly a cycling thermostat will switch off between one hundred twenty and one hundred sixty degrees fahrenheit depending on the thermostat refer to the designation printed on the part itself to test the thermostats response to temperature change placed the component on an electric griddle or skillet and set the heat to the appropriate temperature if the thermostat switches off within five percent of that temperature the part is functioning properly if the thermostat does not switch off or switches off prematurely the thermostat is faulty and will need to be replaced